Keg Dispensing Supplies

Just what the party ordered! A black picnic tap on one end of a 4-foot length of 3/16 in. ID thick walled tubing and a ball lock disconnect with 3/16 in. swivel nuts on the other. Both ends are attached with oetiker-style clamps, which have been crimped on for a tight connection! Be the life of the party by bringing this (and a full keg) to the next get-together!

A great, easy way to make CO2 and keg connections!The pin lock gas dispensing kit is a 3-foot length of 5/16" ID Bevlex tubing with a ball lock gas disconnect and 5/16" swivel nut set worm-clamped on one end, and a small worm clamp on the other that can be used to connect the assembly to a CO2 manifold or regulator. Always good to have around, especially for carbonating several kegs at once!

This CO2 shutoff with barb and check valve is ideal for use with CO2 regulators and manifolds! It has 1/4" MPT right-hand threading on one side that threads into most standard regulators and manifolds. On the other end is a standard 3/8" barb, which works perfectly with standard CO2 gas line. Get one of these to replace a damaged or missing shutoff, put on a wye splittler, or create your own CO2 apparatus!

A bonnet angler is a little piece that comes in handy when trying to use an extra-long tap handle on a kegerator that has a flat surface, such as a converted refridgerator. Often, a longer tap handle won't have the clearance necessary, and will hit the body of the kegerator, not able to fully shut the beer faucet. Alleviate these problems with a bonnet angler! The bonnet angler creates a slight forward lean, giving you room to proudly display your long tap handles!

This is a replacement plunger shaft assembly for standard faucets. It joins with the faucet lever and moves back and forth to allow beer to flow from the faucet. If you need a replacement for an old standard faucet, Great Fermentations has one for you!

One of the most indispensible washers in modern history! Without this washer, there would be leaky kegs on college campuses and at house parties across the country. This is the washer that fits on the bottom of a standard American "D" style coupler. These washers have a tendency to come off during removal after a keg blows. In case this happens to you, be sure to get an extra washer and keep the beer flowing!

Individual 16 gram Co2 non-threaded bulb for use with our Cornelius Keg CO2 Charger (Item # 4990)

3/16" is the standard inner diameter for most serving systems. This 3/16" tubing is thin walled and very economical. We use it in making our dispensing line assemblies. It is durable and works well in most dispensing applications.

Inner Diameter: 3/16 in.
Outer Diameter: 5/16 in.

This CO2 shutoff with 1/4" MPT threading and check valve is ideal for use with CO2 regulators and manifolds! It has 1/4" MPT right-hand threading on one side that threads into most standard regulators and manifolds. On the other end is standard 1/4" MFL threading, which works perfectly with standard swivel nut sets and other 1/4" MFL fittings. If using a swivel nut set, we recommend using a plastic flare fitting as well, in order to create a good seal. Get one of these to replace a damaged or missing shutoff, put on a wye splittler, or create your own CO2 apparatus!

Have some extra tubing on hand for all your kegging needs! 5/16" inner diameter tubing is the standard tubing used in kegging and carbonation systems in the U.S. The Bevlex tubing we carry is thick-walled for extra protection and security when carbonating. This can be used on all standard CO2 connections in your draft system.

Inner Diameter: 5/16 in.
Outer Diameter: 9/16 in.

A 4-way manifold is the perfect way to carbonate four kegs at once, or to pressurize kegs and run a Blichmann BeerGun at the same time! The CO2 can be hooked up from the regulator via the barb on the side of the manifold using standard 5/16" ID Bevlex tubing, and the other barbs can be run with the same tubing to gas disconnects for carbonating and dispensing from kegs, or to other CO2 driven devices. When mounted, the barbs run straight downward. Includes shutoff valves on the four top barbs on the manifold, which give another level of protection from lost CO2!

This is a replacement brass faucet lever for standard faucets. It is the brass piece that the faucet knob or handle screws onto, and fits into the plunger assembly. It moves forward and backward, working in tandem with the plunger assembly to allow beer to flow. These brass levers are known to break every once in awhile, so if you need a replacement, we have one for you right here!

Oetiker clamps provide a permanent clamping solution! This style of clamp has a 1-ear design, which means they are crimped at a single point on the clamp to create a superior seal over your tubing. These small Oetiker clamps are often used on 3/16" thin-walled tubing that is used in some liquid applications and on thin-walled liquid draft lines. These clamps hold tight, creating a great seal that holds for a long time! Some people prefer these for more permanent systems. If you are looking to switch over to a snug seal that lasts, make sure you use Oetiker clamps!

This stainless steel tee is perfect for gas application, but can be used wherever a tee with hose barb fittings is required. It has three 3/8" barb connections, one on all ends, and is therefore able to split gas off in two separate directions from the source.

Beer shanks to make all your dispensing dreams come true! These chrome plated brass shanks are used in a variety of setups to create draft systems. A 3/16" bore is perfect for liquid dispensing of all types, including sweet sweet beer. This 5" shank (actual measurement: 5 1/8") is slightly longer than the standard 4" shank and works when you need just a little more length. Simply drill out your hole, place your shank through, and lock in place with the included lock nut. A faucet can then be attached to the outside of your draft setup, whether it be a kegerator, keezer or jockey box! Also needed on the inside is a 3/16" tailpiece, neoprene beer washer and beer nut.

The secret weapon for keeping a clean brewery! A double ended brush can come in handy for cleaning all those hard-to-reach places, not only in your dispensing system, but also in your brewing equipment. The two ends have two different sizes brushes, which come in handy in cleaning faucet parts, keg posts, dip tubes, racking arms, ball valves, bottle fillers...the list goes on! Keep every nook and cranny of your brewing equipment clean with one of these. Highly recommended to anyone who owns a keg or a permanent dispensing setup.

A black plastic picnic faucet comes in handy in a pinch! Affectionately referred to as a cobra tap, this is a fairly simple dispensing mechanism. When the lever is pressed, the rubber gate is lifted, allowing beer to flow. These picnic faucets come apart easily for cleaning, and feature a barbed end that can fit on standard beer line. Make your own or keep one on hand in case the unthinkable happens!

Finally, a standard faucet made of above-standard material! These standard faucets are anything but standard, with full stainless steel bodies and levers. Stainless steel is the holy grail of beer materials! Sleek and stylist, it not only looks great, but is durable and will last longer than chrome or brass faucets. The simple design means that the faucets are easy to take apart and clean. For beer faucets that will last longer, stainless steel faucets can't be beat!

These quick connects come in handy for quickly connecting to and disconnecting from connections of all kinds! This is the female side that has a gray disconnect button for quickly disconnecting from the male end. It has a 1/4" straight barb to hook up to 1/4" ID tubing. It has a temperature tolerance range from -40 to 180F and a vacuum pressure tolerance of 120 PSI. This female piece is used with the 1/4" Quick Connect Insert, item #05P01-122.

Keep that check valve ball from escaping with a check valve ball retainers! This little winged piece of plastic fits in the shaft of your standard sanke coupler, holding the check valve ball in place so that backflow does not become an issue. Protect the investment of your beer and dispensing equipment by having one of these on hand should the unthinkable loss of the original retainer occur!

Gas lost in your CO2 system can lead to a shorter life span of your CO2 cylinders. Prevent CO2 loss with a washer! A plastic CO2 washer fits between your CO2 cylinder and regulator and helps to create a good seal. A good seal ensures that you don't lose gas when carbonating or serving. These plastic CO2 washers fit Taprite brand regulators, as well as many standard-sized CO2 regulators. Keep a few on hand in case of an emergency!