Keg Dispensing Supplies

The following beer keg dispensing equipment allows you to dispense and serve homebrew without all the hassle of bottles. Choose from homebrew kegerators, homebrew keg dispensing systems or portable homebrew setups.

Showing 21 products

Offset CO2 Wrench

Rustproof wrench for CO2 nut on regulator. The right wrench, right where you need it, when you need it.

GF_20K08-104
$3.99

Wye Splitter

A Y-shaped connector used to split CO2 from a regulator that only has one outlet to two. Measurements are 1/4" MPT X 1/4" FPT X 1/4" FPT. Perfect for use in sending CO2 to both a keg and the Blichmann BeerGun at the same time! Also useful in other applications when CO2 needs to be split two ways.

GF_05B03-121
$11.99

3/16" Tailpiece

This 3/16" tailpiece works with standard 3/16" ID liquid side tubing in a range of liquid dispensing applications. Most commonly, this tailpiece is used with a beer nut and a neoprene beer washer on the end of a shank as part of a faucet draft system. However, they are also used on sanke couplers for the liquid dispensing side. They can come in quite handy when replacing preinstalled liquid side connections in kegerators.

GF_05C08-130
$1.49

5/16" Tailpiece

This 5/16" tailpiece works with standard 5/16" ID CO2 tubing. Most often, these are found on the CO2 side of sanke couplers. Used in conjunction with a beer nut and a neoprene beer washer, these tailpieces can create a tight seal for CO2. Useful as a replacement on kegerator setups, make sure you have one on hand in your draft emergency kit!

GF_05C08-132
$1.49

Black Plastic Flange for Beer Shank

This is a black plastic flange, the type that comes with standard beer shanks. It makes your custom kegerator look nice and professional, covering up drilled holes and providing a nice background for your beer faucet. If yours are damaged, replace them with this flange!

GF_12B03-184
$2.99

Brass Regulator Stem LHT

A brass regulator stem is the part that protrudes out from your regulator and attaches, via a regulator nut, to your CO2 cylinder. This is a left-hand threaded stem which should work on most standard CO2 regulators that take a left-hand thread. This works wonderfully as a replacement if your regulator stem is damaged or missing!

GF_02A03-103
$4.99

Lock Nut for Tower

This is a replacement brass lock nut for the shank on your tower. It works perfectly well on most standard tower shanks used in beer towers. If you need a replacement, we've got one for you right here!

GF_12B03-162
$2.49

5/16" Barbed Swivel Nut Set

A swivel nut set with a barb for your gas side connections! These swivel nut sets come with a standard 1/4" female flared nut and a 5/16" barb that can be used with standard 5/16" ID gas tubing. These can be connected directly to the standard liquid disconnects that we offer, or used with a plastic flare fitting for any direct metal-on-metal connections.

GF_04C03-293
$2.99

90 Degree 3/16" Tailpiece

A bent tailpiece can come in extremely handy when connecting liquid lines in hard-to-reach places, such as kegerator towers or homemade keezers and kegerators. Not only that, but a 90 degree bend just makes sense in some setups! This tailpiece has a standard 3/16" barb, perfect for liquid line applications. It is often used with a beer nut and a neoprene beer washer for a secure seal.

GF_03B03-133
$7.99

Faucet (spanner) Wrench

Everyone with a draft system should own a spanner wrench! This little curved tool hooks into the holes on the faucet coupler to loosen or tighten your faucet as needed. Even if you bought a draft system preassembled, you will still want to take the faucet off and clean it periodically to ensure the cleanest pour possible.

GF_20B03-125
$3.99

Economy Twist Sanke Pump Tap

Always have a tap when the party demands one! This economy twist sanke pump tap is a classic party-style pump coupler. It features a pump for pressurizing a keg with air, a twist-style coupling mechanism similar to those found on low-profile sanke couplers, and a short black picnic faucet. This is the perfect, economical solution for kegs that are going to be quickly consumed. Instead of paying the liquor store multiple deposits, invest in a pump tap and always be prepared to get the party started!

GF_18B03-240
$59.99

Euro Sanke "S" Coupler

From Taprite comes this "S" style keg coupler, also known as a tap. This is the part that really gets the beer flowing! Chrome-plated brass construction ensures for longevity of the coupler, so that you can keep the beer flowing keg after keg. The "S" style coupler is a common European style coupler used by many leading breweries in Europe, including Stella Artois, Heineken, Beck's, Amstel, Newcastle, Pilsner Urquell, Lindeman's, and Huyghe, makers of Delirium Tremens. It is similar to a North American "D" style coupler, but runs about a 1/4" deeper into the keg. This coupler comes with a standard 5/16" gas barb, check valve and beer nut on the gas side. Not included with this coupler are the neoprene washer, 3/16" barb liquid tailpiece and beer nut.

GF_07S07-123
$35.99

1/4" Quick Connect Insert

These quick connects come in handy for quickly connecting to and disconnecting from connections of all kinds! This is the male side that has a black gasket that allows it to quickly connect to the female end. It has a 1/4" straight barb to hook up to 1/4" ID tubing. It has a temperature tolerance range from -40 to 180F and a vacuum pressure tolerance of 120 PSI. This male piece is used with the 1/4" Quick Disconnect Body, item #05P01-120.

GF_05P01-122
$9.99

Female 3/8" In-line Hose Barb

These quick connects come in handy for quickly connecting to and disconnecting from connections of all kinds! This is the female side that has a gray disconnect button for quickly disconnecting from the male end. It has a 3/8" straight barb to hook up to 3/8" ID tubing. It has a temperature tolerance range from -40 to 180F and a vacuum pressure tolerance of 120 PSI. This female piece is used with the Male 3/8" In-line Hose Barb, item #05P01-123.

GF_05P01-121
$8.99

Regulator Gauge - Tank Pressure LHT

Have you ever damaged a gauge on your CO2 regulator? We've got the replacements you need! This is a left-hand threaded replacement tank pressure gauge for your CO2 regulator. These come standard on dual gauge regulators, and this one works with regulators that take a left-hand threaded gauge.

GF_03G07-283
$11.99

Brass Coupling Nut for Faucet

Replace your missing or damaged coupling nut with one of these brass replacements from Great Fermentations! These also work well with a faucet adapter (item #17C13-100). Put one of these on the faucet adapter, add a faucet and a liquid disconnect on the other end, and you have yourself a faucet assembly ready to put on a cornelies keg!

GF_12B03-180
$3.99

Stout Faucet Assembly with 4 in. Shank

Want to pour the perfect stout or nitro beer every time? With the stout faucet assembly, you'll be able to add a stout faucet to your kegerator that pours a rich, creamy head on all nitrogenated or beer gas beers. Perfect for Guinness or Guinness clone beers, but can be used with a range of beer gas beers or beers on nitro, such as the nitrogenated IPAs and Imperial Red Ales that have become popular as of late.

Assembly Includes the Following:
Stout faucet (Chrome plated body with a stainless spout and stainless restrictor plate).
Faucet knob
Chrome-plated 4 1/8 in. shank with 3/16 in. bore
Beer nut, neoprene washer and 3/16 in. tailpiece

Get this assembly, add it to your kegerator or keezer system, and impress all your friends with perfect pours every time!

GF_GF205
$91.99

Check Valve Ball

Simply put, this is a check valve ball. It works with standard NADS American "D" sanke couplers, as well as other sanke couplers that use the same ball. This helps to keep your beer in "check" by blocking backflow of liquid back through the valve. In some instances, people will lose the ball while cleaning the coupler. If this happens, never fear! We've got a replacement for you so you can keep that beer safely flowing!

GF_12S07-107
$1.49

Grommet for Tower

Make your coonecitons tight! With this grommet, you can create the perfect seal for your liquid tower elbow. This will allow the beer to continue flowing freely for years to come!

GF_12B03-226
$2.49

Standard Chrome Beer Faucet with Brass Lever

Standard faucets are just that...standard faucets for pouring beer! They come standard with a number of kegerators and dispensing setups, and can be found on jockey boxes, homemade beer fridges and keezers, just about anywhere you find beer! Economical, they are easy to take apart and clean, with just a few moving parts that can easily be replaced if needed. These make great replacement faucets for damaged faucets on existing setups, or work well on new installations as well! These can be put on the end of a shank for a new installation.

GF_12B03-118
$17.99

1/2" ID Bevlex Tubing

This Bevlex tubing measures 1/2" inner diameter, making it perfect for use with a 1/2" racking cane or large auto-siphon. The thicker walling is kink-resistant, and is perfect for more rigorous applications. Some people have been known to use this tubing for racking using a vacuum pump, and others just prefer it to thin-walled tubing because of its durability. Whatever you use it for, we've got it here for you!

Inner Diameter: 1/2 in.
Outer Diameter: 3/4 in.

GF_08A05-127
$0.99

Showing 589 - 609 of 668 results