Keg Dispensing Supplies

One of the most indispensible washers in modern history! Without this washer, there would be leaky kegs on college campuses and at house parties across the country. This is the washer that fits on the bottom of a standard American "D" style coupler. These washers have a tendency to come off during removal after a keg blows. In case this happens to you, be sure to get an extra washer and keep the beer flowing!

Beer shanks to make all your dispensing dreams come true! These chrome plated brass shanks are used in a variety of setups to create draft systems. A 3/16" bore is perfect for liquid dispensing of all types, including sweet sweet beer. This 6" shank (actual measurement: 6 1/8") is longer than the standard 4" shank and works when you need just a little more length. Simply drill out your hole, place your shank through, and lock in place with the included lock nut. A faucet can then be attached to the outside of your draft setup, whether it be a kegerator, keezer or jockey box! Also needed on the inside is a 3/16" tailpiece, neoprene beer washer and beer nut.

Beer nuts are a standard hex nut used on many beer dispensing connections. Most notably, they are used on the end of faucet shanks and on sanke couplers. They accept a standard tailpiece, such as a 3/16" tailpiece for liquid applications or a 5/16" tailpiece for CO2 applications. In addition, neoprene beer washers are also used in conjuction to create a seal. These are nickel plated brass hex nuts with a 7/8" x 14 straight pipe thread that is standard in the U.S. beer industry. Always keep a few of these on hand for any situation that may arise!

A black plastic picnic faucet comes in handy in a pinch! Affectionately referred to as a cobra tap, this is a fairly simple dispensing mechanism. When the lever is pressed, the rubber gate is lifted, allowing beer to flow. These picnic faucets come apart easily for cleaning, and feature a barbed end that can fit on standard beer line. Make your own or keep one on hand in case the unthinkable happens!

Make your coonecitons tight! With this grommet, you can create the perfect seal for your liquid tower elbow. This will allow the beer to continue flowing freely for years to come!

This is a replacement washer for the lever on the old 425 series Perlick faucets. If your old faucet is in need of some new washers, we've got you covered! These are the perfect replacement for old, disused Perlick 425 series faucets.

Use your CO2 regulator with a beer gas tank with this CO2 regulator to nitrogen adapter! This part is approximately 3 inches long and will adapt a female CGA-320 fitting (which is the standard fitting on a standard CO2 regulator) to a male CGA-580 fitting (which is the standard fitting on a beer gas tank). This way, you will be able to use your existing CO2 regulator on a beer gas tank without buying a new nitrogen regulator! This works great for the creamy beer enthusiast who occasionally uses beer gas! Please note that this connection should NOT be used with pure nitrogen due to the higher pressures that pure nitrogen is kept under. This should work great for most people who occasionally use beer gas to give their beers that extra creaminess!

Have you ever damaged a gauge on your CO2 regulator? We've got the replacements you need! This is a right-hand threaded replacement output pressure gauge for your CO2 regulator. It measures output pressure between 0 and 60 PSI and works with regulators that take a right-hand threaded gauge.

Do you want to serve perfect pints of nitrogenated beers every time? The cascading nitrogen bubbles coming from a classic Irish stout come to mind, as do other styles, such as IPAs, imperial red ales, and classic British pub ales that are sometimes served on nitrogen. To pour these beers perfectly, you need a stout faucet...and we've got just the one for you! This stout faucet is the same classic faucet design that Guinness is poured from at your favorite traditional Irish and British pubs. In addition, many bars and restaurants use this style for pouring any nitrogenated beers! Featuring a stainless steel straight nozzle with a stainless steel restrictor plate that forces the beer to come out creamy and smooth, the design allows for pulling forward to pour beer and pulling back to give a creamy froth to the beer. Use with beer gas to achieve that perfect pour!

This faucet features a chrome plated body, with a stainless steel restrictor disk and nozzle.

A swivel nut set with a barb for your gas side connections! These swivel nut sets come with a standard 1/4" female flared nut and a 5/16" barb that can be used with standard 5/16" ID gas tubing. These can be connected directly to the standard liquid disconnects that we offer, or used with a plastic flare fitting for any direct metal-on-metal connections.

These quick connects come in handy for quickly connecting to and disconnecting from connections of all kinds! This is the female side that has a gray disconnect button for quickly disconnecting from the male end. It has a 3/8" straight barb to hook up to 3/8" ID tubing. It has a temperature tolerance range from -40 to 180F and a vacuum pressure tolerance of 120 PSI. This female piece is used with the Male 3/8" In-line Hose Barb, item #05P01-123.

Change out all your standard o-rings on a cornelius keg with this o-ring replacement set! This comes with one center closure o-ring, two post o-rings, and two dip tube o-rings. These are all the standard o-rings that come on a Cornelius keg. Change these out periodically, when your connections get hard to make or when your o-rings begin to fray. Always handy to have on hand in case of a kegging emergency!

Rustproof wrench for CO2 nut on regulator. The right wrench, right where you need it, when you need it.

Beer shanks to make all your dispensing dreams come true! These chrome plated brass shanks are used in a variety of setups to create draft systems. A 3/16" bore is perfect for liquid dispensing of all types, including sweet sweet beer. This 4" shank is a standard size (actual measurement is 4 1/8") and works on most applications. Simply drill out your hole, place your shank through, and lock in place with the included lock nut. A faucet can then be attached to the outside of your draft setup, whether it be a kegerator, keezer or jockey box! Also needed on the inside is a 3/16" tailpiece, neoprene beer washer and beer nut.

Simply put, this is a check valve ball. It works with standard NADS American "D" sanke couplers, as well as other sanke couplers that use the same ball. This helps to keep your beer in "check" by blocking backflow of liquid back through the valve. In some instances, people will lose the ball while cleaning the coupler. If this happens, never fear! We've got a replacement for you so you can keep that beer safely flowing!

Brilliant! A small brush that fits over the end of your cap and kills two birds with one stone: keeps your faucet clean, and keeps flies out! When the heat of summer comes around and old beer heats up in the metal interior of your faucet, flies start hovering around. And what is worse than getting a cup of beer full of flies? Protect your beer by having a faucet plug with brush that scrubs out the inside of your tap and keeps flies out!

This is a male compression nut for beer towers. It goes in the end of a shank and accomodates a liquid tower elbow to get the beer flowing! You may also need a tower grommet to help create a good seal. With these, you should have the beer flowing from your tower in no time!

Oetiker clamps provide a permanent clamping solution! This style of clamp has a 1-ear design, which means they are crimped at a single point on the clamp to create a superior seal over your tubing. These large Oetiker clamps are often used on 5/16" thick-walled tubing that is used in CO2 connections on kegging and draft systems. These clamps hold tight, creating a great seal that holds for a long time! Some people prefer these for more permanent systems. If you are looking to switch over to a snug seal that lasts, make sure you use Oetiker clamps!

Three is better than one! This 3" beer tower extension not only extends your tower, but comes with two shanks for adding two more faucets to your tower setup. With the existing fauet, this means that you can have up to three beer faucets on your setup! Perfect for going big with your existing 3" beer tower, get your extension today!

Want to pour the perfect stout or nitro beer every time? With the stout faucet assembly, you'll be able to add a stout faucet to your kegerator that pours a rich, creamy head on all nitrogenated or beer gas beers. Perfect for Guinness or Guinness clone beers, but can be used with a range of beer gas beers or beers on nitro, such as the nitrogenated IPAs and Imperial Red Ales that have become popular as of late.

Assembly Includes the Following:
Stout faucet (Chrome plated body with a stainless spout and stainless restrictor plate).
Faucet knob
Chrome-plated 4 1/8 in. shank with 3/16 in. bore
Beer nut, neoprene washer and 3/16 in. tailpiece

Get this assembly, add it to your kegerator or keezer system, and impress all your friends with perfect pours every time!

This CO2 shutoff with 1/4" MPT threading and check valve is ideal for use with CO2 regulators and manifolds! It has 1/4" MPT right-hand threading on one side that threads into most standard regulators and manifolds. On the other end is standard 1/4" MFL threading, which works perfectly with standard swivel nut sets and other 1/4" MFL fittings. If using a swivel nut set, we recommend using a plastic flare fitting as well, in order to create a good seal. Get one of these to replace a damaged or missing shutoff, put on a wye splittler, or create your own CO2 apparatus!